Integrity first
  Integrlty first,service fist
全屏通栏广告背景
导航菜单
全站搜索
搜索
Hotline:0571-86688649
All our efforts are just for your worries!
Hangzhou Sansi Instrument Co., Ltd.
文章正文
Bolt puller instructions
作者:管理员    发布于:2019-09-02 15:11:04    文字:【】【】【
Anchor puller meets standards
Production according to "MTT 979-2006 Coal Mine Bolt Tension Meter"
Anchor drawing instrument shows the main technical parameters
Model Cylinder center hole diameter Cylinder stroke Measuring range Weight Resolution
ZY-5T 16mm 50mm 0~50 KN 4.5Kg
 
 
0.1KN
ZY-10T 27mm 60mm 0~100 KN 7.5Kg
ZY-20T 34mm 70mm 0~200KN 14Kg
ZY-30T 45mm 80mm 0~300 KN 16Kg
ZY-50T 45mm 80mm 0~500 KN 29Kg
ZY-60T 60mm 100mm 0~1000KN 65Kg
ZY-100T 90mm 150mm 0~1000KN 65Kg
1. (50-1000) kN hollow self-resetting hydraulic cylinder
2, manual pump one
3, intelligent digital display pressure gauge
4, a high pressure oil pipe
5, a precision sensor
6, a manual
7. One warranty card and one certificate
8, a carrying case
Anchor drawing instrument description
The bolt puller is an indispensable on-site inspection instrument for quality inspection units. Anchor puller It is mainly used to detect the anchoring force of various anchors, steel bars and other anchors. The bolt puller consists of a manual pump, a hydraulic cylinder, an intelligent digital pressure gauge, a high pressure oil pipe with a quick connector, an anchor and a portable carrying case. The hydraulic cylinder is hollow self-resetting type, and the intelligent digital pressure gauge is directly readable. Take the anchor pull value (kN), and have peak hold, storage and query functions, especially suitable for on-site use, easy to operate, easy to learn and use.
Anchor puller description product introduction:
ZY series bolt puller is composed of manual pump, hollow hydraulic cylinder, intelligent data configurator (Chinese type, digital type), high pressure oil pipe with quick connector, anchor, tie rod, conversion head and portable suitcase. The hydraulic cylinder is manually reset, easy to operate, easy to learn and use.
Introduction to the bolt puller:
ZY series bolt puller is divided into 5 tons, 10 tons, 20 tons, 30 tons, 50 tons, 60 tons and 100 tons; the instrument consists of manual pump, hollow hydraulic cylinder, Chinese intelligent data processor, high voltage with quick connector. It consists of tubing, anchors, adapter rods and carrying cases. The values in the instrument are displayed as numbers, which can directly read the bolt pull force value (kN), automatic calculation, peak hold, storage and query functions. It is especially suitable for laboratory and field use, easy to operate, easy to learn and use.
ZY series bolt puller is a self-developed product of Hangzhou Sansi Instrument Co., Ltd. It is used to detect various bolts, steel bars, expansion bolts and anchors' pull-out resistance. It can also be used for on-site pull-out testing (testing) of glass curtain walls. It is an indispensable testing instrument for all quality inspection units.
Mechanical parts features:
Nickel plated piston and sliding sleeve;
Surface corrosion resistant electrostatic spraying;
New sealing ring and reliable operation;
Automatic spring reset, simple structure, and a hollow part with a dust jacket;
Overload protection
The two unique pressurization methods can be either pressurized or pressurized. Is a replacement product of the traditional puller
Bolt puller instructions instructions:
1. Check the oil quantity: If the hydraulic cylinder piston is not fully retracted into the cylinder body, first connect it to the hand pressure pump through the oil pipe, and loosen the unloading valve on the pump body counterclockwise to discharge the hydraulic oil in the jack. Go to the hand pump reservoir. Unscrew the oil filling valve and check the oil quantity. If the oil is not full, you can add N46 wear hydraulic oil or No. 20 oil.
2. Exhaust: After the hydraulic system is assembled, air is often mixed in the oil storage cylinder, oil pipe and hydraulic cylinder. In order to make the hydraulic system normal, the air must be drained. The method is to place the manual pump slightly higher than the hydraulic cylinder, press the manual pump to extend the hydraulic cylinder piston, and then open the unloading valve to retract the piston for several times. If necessary, open the oil filling valve to remove air from the oil reservoir.
3. Detecting the anchor: connect the oil pipe to the jack, and check the oil quantity, exhaust and pressure gauge according to the requirements of items 1 and 2 above. As shown in Figure 2, pull the lever (please specify the specifications when ordering or bring it according to the actual test conditions) and screw it to the end of the bolt. If the outer diameter of the inner thread of the rod is larger than the center hole of the cylinder, add a long sleeve at the bottom of the cylinder. Put on the hydraulic cylinder (to make the piston end outward), then screw on the nut and tighten the relief valve clockwise.
Press the handle of the oil pump, the force should be even, do not use too much force, stop the pressure when the reading on the pressure gauge reaches the requirement. Note that the hand pump must be placed horizontally to work. After the test is completed, the discharge valve should be loosened in the direction of the reverse needle, so that the pressure gauge reads zero, and then the components are removed from the anchor.
Anchor drawing instrument instructions
1. The hydraulic oil to be used in this product is L-HM32# anti-wear hydraulic oil. The best use environment is -20 °C ~ 45 °C. It is strictly forbidden to use alcohol, glycerin, brake oil, ordinary engine oil, etc. as hydraulic oil.
2. The tool has a rated pressure of 60 MPa and a maximum pressure of 80 MPa. In addition, in order to increase the service life of the pressure gauge, it generally does not exceed 75% of the maximum pressure.
3. The joints of the oil pump and the cylinder of the tool are subjected to high pressure. Therefore, the joint should be protected, and the joint should not be damaged and the seal and normal work should be affected. Do not use the wrench to pull the joint on the hose to prevent the buckle from loosening. And the rubber leaking oil is scrapped.
4. The oil cylinder and piping of the tool should always be cleaned with clean kerosene to ensure that the tool works properly and prolongs its service life.
5. Note: Do not block dirt on the inlet and outlet of each oil circuit. This product is guaranteed for one year and is free to use for users.
 
Hangzhou Sansi Instrument Co., Ltd. Main Products:
Anchor dynamometer, geotechnical instrument, building test instrument, highway instrument, cement test instrument, asphalt instrument, analytical laboratory instrument, sputum test instrument, various analytical standard sieve, product warranty for one year, lifetime maintenance
Sales hotline: 0571-86688649
QQ: 2318806276

Tel :0571-86688649
Fax : 0571-86688346
Tel:13567560820 Manager Chen
          13216192676 Manager Wang Lili
Rul:www.hzssyq.com
Mail: hzssyq@126.com
Add:No. 601, Jiangling Road, Binjiang District, Hangzhou


新闻中心

NEWS CENTER
Article classification
当前位置
全屏通栏广告背景

Sweep the phone preview

FAX: 0571-86688346
TEL: 0571-86688649
URL:www.hzssyq.com
ADD: No. 601, Jiangling Road, Binjiang District, Hangzhou
自定模版
向下滚动显示返回顶部
TOP
Hangzhou Sansi Instrument Co., Ltd.

Hangzhou Sansi Instrument Co., Ltd. all rights reservedTechnical Support:7m 

Business Registration Number:91330108552653595D